Endress+Hauser Liquisys M CLM 223 Operating Instructions Manual Download Page 18

Page: 18 / 83

3.5

Measuring cell installation and cable connection

Measuring cable connection

The conductivity measuring cells are
connected using a special, shielded
multi-core cable.
Termination instructions are supplied with the
measuring cables.
Use junction box VBM (see chapter 9) to
extend the measuring cable.

Structure and termination of measuring cables

Special measuring cable required for connection of conductivity measuring cells

Measuring cell type

Cable

Extension

2-electrode measuring cell with or
without temperature sensor Pt 100

CYK 71

Junction box VBM
+ CYK 71

Inductive measuring cell CLS 50

Cable permanently
attached to sensor

Junction box VBM
+ CLK 5

Maximum cable length

Conductive conductivity
measurement

max. 100 m with CYK 71 (corresponds to 10 nF)

Resistance measurement

max. 15 m with CYK 71 (corresponds to 2 nF)

Inductive conductivity measurement

max. 55 m (with CLK 5 and sensor cable)

KABEL.CDR

Inner conductor

Green (11)

White (12)

Yellow (13)

CYK 71

Semiconductor

screen

Screen

Green (11)

White (1)

Yellow (13)

Brown

(unused)

Semiconductor

screen

White

Red

CLK 5

Brown

(unused)

Black

(84)

(83)

(84)

(83)

(15)

(16)

Fig. 3.13

Structure of special
measuring cables CYK 71
(left) and CLK 5 (right)

Installation

Liquisys M CLM 223 / 253

Hauser

Summary of Contents for Liquisys M CLM 223




















































































Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands

Endress+Hauser Liquisys M CLM 223, Operating Instructions Manual

Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands