Endress+Hauser Liquisys M CLM 223 Operating Instructions Manual Download Page 29

Page: 29 / 83

5.2.2

Setup 2

Coding

Field

Selection or range

Factory setting

Display

Info

Selection of unit to
be displayed

auto,

µS/cm, mS/cm,

S/cm, µS/m, mS/m,
S/m, auto

Ω

, k

Ω⋅

cm,

Ω⋅

cm, k

Ω⋅

When “auto” or “auto

Ω

” is

selected, the maximum
resolution possible is
automatically selected.
A4 not active if A1 = conc.

Enter cell constant
for measuring cell
connected

cond:

1.000 cm

–1

ind:

1.98 cm

–1

MOhm:

0.01 cm

–1

0.0025 ... 99.99 cm

–1

Refer to the measuring cell
quality certificate for the exact
cell constant.

Enter cable
resistance

Ω

0 ... 99.99

Ω

Only if A1 = cond
(conductive instrument).
See chapter 10.

Enter measured
value damping

1 ... 60

Measured value damping causes
averaging over the specified
number of individual measured
values. It is used, for example, to
stabilise the display with
applications that fluctuate a great
deal. There is no damping if “1”
is entered.

Factory settings are printed in

bold

face;

base version does not include functions in italics.

Coding

Field

Selection or range

Factory setting

Display

Info

Function group
SETUP 2

Initial display in function group
SETUP 2.

Selection of
temperature
sensor

Pt100

Pt1k = Pt 1000
NTC30
fixed

“fixed”:
No temperature measurement
if a fixed temperature value is
preset.

Selection of
temperature
compensation
type

lin

linear

Tab = table
NaCl = common salt

(IEC 746)

Pure = ultrapure water
none

This option is not displayed for
concentration measurement.

“Pure” is only available on
conductive instruments.

auto

Unit

1.000

Cellconst

1/cm

Ohm cable

Damping

SETUP 2

ProcTemp.

Pt100

TempComp.

lin

LM253E5A.CHP

Liquisys M CLM 223 / 253

Instrument configuration

Hauser

Summary of Contents for Liquisys M CLM 223




















































































Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands

Endress+Hauser Liquisys M CLM 223, Operating Instructions Manual

Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands