Endress+Hauser Liquisys M CLM 223 Operating Instructions Manual Download Page 67

Page: 67 / 83

8.5.2

Dismantling of CLM 253

• Open and remove the connection

compartment cover (item 420).

• Pull off the power connection terminal (item

470) to de-energize the instrument.

• Open the display lid (item 410) and

remove the ribbon cables (item 310 / 320)
on the side of the electronics box (item
330).

• Removal of central module (item 40):

Loosen the screw (item 450b) in the
display lid.

• Removal of electronics box (item 330):

Unscrew screws (item 450a) in bottom of
housing 2 revolutions, then slide entire box
backward and remove towards the top.
Make sure that the module catches do not
come unlatched! Bend the module latches
outward and remove the module(s).

• Removal of docking assembly (item 340):

Remove the screws (item 450c) in the
bottom of the housing and remove the
entire assembly towards the top.

8.5.3

Assembly of CLM 253

• Insert the module(s) in the electronics box

guide rails carefully and latch into the
lateral lugs in the box.

• Incorrect assembly is not possible!

Modules inserted in the electronics box

incorrectly are not operable since the
ribbon cables cannot be inserted.

• Make sure that the cover gaskets are intact

since they are required to guarantee
protection class IP 65.

8.5.4

Spare parts for CLM 253

Item

Designation

Name

Function

Order number

Power supply unit

LSGA

100/115/230 V AC

51500317

Power supply unit

LSGD

24 V AC + DC

51500318

290

Relay module

LSR1-2

2 relays

51500320

300

Relay module

LSR1-4

4 relays

51500321

Conductive central module

LSCH-S1

1 current output

51501210

Conductive central module

LSCH-S2

2 current outputs

51501212

Conductive central module

LSCH-H1

1 current HART

51501213

Conductive central module

LSCH-H2

2 current HART

51501214

Conductive central module

LSCP

Profibus PA / no current outp.!

51501215

Inductive central module

LSCH-S1

1 current output

51501216

Inductive central module

LSCH-S2

2 current outputs

51501218

Inductive central module

LSCH-H1

1 current HART

51501219

Inductive central module

LSCH-H2

2 current o HART

51501220

Inductive central module

LSCP

Profibus PA / no current outp.!

51501221

240

Conductivity transmitter

MKIC

Cond. + temp. input

51501206

370, 410,
420, 430

Housing cover assembly

Display lid, connection

compartment cover, front

membrane, hinges

51501068

400, 480

Housing bottom (mechanical)

Bottom, cable glands

51501072

330, 340,

450

Internal housing parts

Docking assembly, empty

electronics box, small parts

51501073

310, 320

Ribbon cables

2 ribbon cables

51501074

430

Hinges

2 pairs of hinges

51501069

470

Power supply terminal strip

Terminal strip, 2-pin

51501079

403

PE terminal strip

PE and screen connections

51501087

LM253E08.CHP

Liquisys M CLM 223 / 253

Diagnosis and corrective maintenance

Hauser

Summary of Contents for Liquisys M CLM 223




















































































Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands

Endress+Hauser Liquisys M CLM 223, Operating Instructions Manual

Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands