Endress+Hauser iTHERM TrustSens TM371 Operating Instructions Manual Download Page 7

Page: 7 / 106

iTHERM TrustSens TM371, TM372

Incoming acceptance and product identification

Hauser

Incoming acceptance and product

identification

3.1

Incoming acceptance

1. Unpack the device carefully. Is the packaging or content damaged?

 The damaged content must not be installed; in those conditions the

manufacturer cannot guarantee the original safety requirements or the material

resistance and cannot be considered as responsible for any consequent damages.

2. Is the delivery complete? Compare the scope of delivery against the information on

your order form.

DELIVERY NOTE

A0028503

Do the nameplate data match the ordering information on the delivery note?

TMT162

TrustSens
TM371, 372

A0028522

Are the technical documentation and additional documents (e.g. certificates)

present?

If one of the conditions does not comply, contact your Hauser distributor.

3.2

Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Enter the serial number from the nameplate in the

W@M Device Viewer

(

www.endress.com/deviceviewer

): All data relating to the device and an overview of

the Technical Documentation supplied with the device are displayed.

Summary of Contents for iTHERM TrustSens TM371











































































































Search results

Summary of Contents for iTHERM TrustSens TM371

Reviews:

Related manuals for iTHERM TrustSens TM371

Brands by name

Popular brands

Endress+Hauser iTHERM TrustSens TM371, Operating Instructions Manual

Search results

Summary of Contents for iTHERM TrustSens TM371

Reviews:

Related manuals for iTHERM TrustSens TM371

Brands by name

Popular brands