Endress+Hauser FieldPort SWA50 Operating Instructions Manual Download Page 70

Page: 70 / 76

Maintenance

FieldPort SWA50

Hauser

5. Wait until the firmware update has been downloaded. The remaining time is

displayed.
 The following view is displayed:

6. Tap either the

Apply

button or the

Later

button.



Apply

button: The FieldPort SWA50 is restarted and the firmware update is

installed on the FieldPort SWA50.

Later

button: The firmware update is not installed until the next time the

FieldPort SWA50 is restarted.

7. Wait for restart.
8. Connect the FieldPort SWA50 to the SmartBlue app again.
9. Use the "Firmware version" parameter to check if the new firmware is installed.

→  49

If the firmware update is not fully downloaded or is not correctly installed, the

FieldPort SWA50 works with the old firmware.

Summary of Contents for FieldPort SWA50













































































Search results

Summary of Contents for FieldPort SWA50

Reviews:

Related manuals for FieldPort SWA50

Brands by name

Popular brands

Endress+Hauser FieldPort SWA50, Operating Instructions Manual

Search results

Summary of Contents for FieldPort SWA50

Reviews:

Related manuals for FieldPort SWA50

Brands by name

Popular brands