Endress+Hauser FieldPort SWA50 Operating Instructions Manual Download

Page: 14 / 76

Installation

FieldPort SWA50

Hauser

5.2.2

"Remote mounting" version

A0043240

 3

Example of remote mounting

FieldPort SWA50 "remote mounting" version

Cable

HART field device

For remote mounting, we recommend the optional mounting bracket. Alternatively,

you can secure the remote version using pipe clips.
"Remote mounting" version of installation process: →  21

5.3

Mounting the "direct mounting" version

NOTICE

Damaged seals.

IP degree of protection is no longer guaranteed.

‣

Do not damage seals.

NOTICE

Supply voltage is present during installation.

Possible damage to the device.

‣

Switch off supply voltage prior to installation.

‣

Make sure the device is de-energized.

‣

Secure it against being switched back on.

"Direct mounting" overview: →  13

Electrical connection: →  29

Tools required

• Wrench AF24

• Wrench AF36

Summary of Contents for FieldPort SWA50













































































Search results

Summary of Contents for FieldPort SWA50

Reviews:

Related manuals for FieldPort SWA50

Brands by name

Popular brands

Endress+Hauser FieldPort SWA50, Operating Instructions Manual

Search results

Summary of Contents for FieldPort SWA50

Reviews:

Related manuals for FieldPort SWA50

Brands by name

Popular brands