ELTEX TAU-32M.IP Operation Manual Download Page 17

Page: 17 / 334

_________________________________________________________________________________

Universal Network Terminal TAU-32M.IP 17



Caller ID in DTMF format;



'Russian Caller ID';



Calling without Caller ID broadcasting;



Hotline/warmline;



Call Hunt;



Call PickUp;



3-way conference (local or using conference server);



Voice message waiting indicator – MWI;



Do Not Disturb.

–

Selection of power supply configuration: from AC or DC network;

–

Ability of monitoring via Web interface:



Subscriber lines status;



Services status;



Hardware platform;



Switch network ports status;

–

Logging;

–

Maintenance of statistics on FXS port operation (port status, number of calls, last number dialed, number

of packets transmitted/received/lost);

–

Direct connection of FXS and FXO ports to each other (only on the TAU32M-M4S4O-R submodule) to

provide communication in case of power failure.

SIP, supported recomendations:

–

RFC 3261 SIP 2.0;

–

RFC 3262 SIP PRACK;

–

RFC 4566 Session Description Protocol (SDP);

–

RFC 3263 Locating SIP servers for DNS lookup SRV and A records;

–

RFC 3264 SDP Offer/Answer Model;

–

RFC 3265 SIP Notify;

–

RFC 3311 SIP Update;

–

RFC 3515 SIP REFER;

–

RFC 3891 SIP Replaces Header;

–

RFC 3892 SIP Referred-By Mechanism;

–

RFC 4028 SIP Session Timer;

–

RFC 2976 SIP INFO Method;

–

RFC 2833 RTP Payload for DTMF Digits, Flash event;

–

RFC 3108 Attributes ecan and silenceSupp in SDP;

–

RFC 4579 SIP. Call Control - Conferencing for User Agents;

–

RFC 3372 SIP for Telephones (SIP-T);

–

RFC 3398 ISUP/SIP Mapping;

–

RFC 3204 MIME Media Types for ISUP and QSIG (ISUP support);

–

RFC 3361 DHCP Option 120;

–

RFC 3966 The tel URI for Telephone Numbers;

–

SIP OPTIONS Keep-Alive (SIP Busy Out);

Summary of Contents for TAU-32M.IP















































































































































































































































































































































Search results

Summary of Contents for TAU-32M.IP

Reviews:

ELTEX TAU-32M.IP, Operation Manual, Page: 17 / 334

Search results

Summary of Contents for TAU-32M.IP

Reviews: