ELTEX SMG-1016M Operation Manual Download Page 21

Page: 21 / 441

SMG Digital Gateway

1.4

Main Specifications

Table below lists main specifications of the terminal.

Table 1 — Main specifications

VoIP Protocols

Supported protocols

SIP-Т/SIP-I

SIP

SIP-Q

H.323v2/v3/v4

MGCP

MEGACO

SIGTRAN (M2UA, IUA)
SIGTRAN (M3UA)

T.38

Audio Codecs

Codecs

G.711 (A/U)

G.729 AB

G.723.1 (6.3 Kbps, 5.3 Kbps)

G.726 (32 Kbps)

Quantity of VoIP channels supported by a submodule depending on the codec type

Codec/packetization time, ms

Channel quantity

G.711 (A/U) / 20-60

G.711 (A/U) / 10

G.729 A / 20-80

G.729 A / 10

G.723.1 (6.3 Kbps, 5.3 Kbps)

G.726 / 20

G.726 / 10

Т.38

128

112

TDM channels per 1 submodule

128

Three-way conferences per 1 submodule

Electrical Ethernet interface specifications

No. of interfaces

SMG-1016M

SMG-2016

Electric port

RJ-45

Data rate, Mbps

Autodetection, 10/100/1000Mbps

duplex

Supported standards

10/100/1000BaseT

Optical Ethernet interface specifications

No. of interfaces

SMG-1016M

SMG-2016

2 combo ports

Optical port

Mini-Gbic (SFP):

1) duplex, double fiber, wave length 1310nm (Single-
Mode), 1000BASE-LX (LС connector), distance — up to
10km, supply voltage — 3.3V

2) duplex, single fiber, reception/transmission wave
lengths 1310/1550nm, 1000BASE-LX (SC connector),
distance — up to 10km, supply voltage — 3.3V

Data rate, Mbps

1000Mbps, duplex

Supported standards

1000BaseX

Not supported in the current firmware version.

Summary of Contents for SMG-1016M


























































































































































































































































































































































































































































Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands

ELTEX SMG-1016M, Operation Manual

Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands