ELTEX SMG-1016M Operation Manual Download Page 383

Page: 383 / 441

SMG Digital Gateway

383

Entering SIPT-mode.

SMG-[CONFIG]-SIP/SIPT/SIPI-INTERFACE[0]>

ipaddr

192.168.16.7

// Define IP address of the communicating gateway

SIPT-Interface[0]. Set ipaddr '192.168.16.7'

SMG-[CONFIG]-SIPT-INTERFACE[0]>

port

5060

// Define UDP port of the communicating gateway used for SIP signalling operation

SIPT-Interface[0]. Set port '5060'

SMG-[CONFIG]-SIP/SIPT/SIPI-INTERFACE[0]>

codec set

0 G.711-a

// Define the codec

SIPT-Interface[0]. Set codec '0'

SMG-[CONFIG]-SIP/SIPT/SIPI-INTERFACE[0]>

codec pte

0 30

// Define packetization time 30ms for G.711

codec

SIPT-Interface[0]. Set pte '30'

SMG-[CONFIG]-SIPT-INTERFACE[0]>

max_active

// Define the quantity of simultaneous sessions

SIPT-Interface[0]. Set max_active '25'

SMG-[CONFIG]-SIPT-INTERFACE[0]>

DTMF mode

RFC2833

// Select DTMF – RFC2833 transmission method

SIPT-Interface[0]. Set DTMF_type '1'

SMG-[CONFIG]-SIPT-INTERFACE[0]>

DTMF payload

101

// Select payload type 101 for RFC2833

SIPT-Interface[0]. Set DTMF_PT '101'

'SIP/SIPT INTERFACE' [00]: id[00]

name: SIP-interface00

mode: SIP-T

trunk: 0

access category: 0

ip:port: 192.168.16.7:5060

codecs:

0 :

codec: G.711-A

ptype: 8

pte: 30

max active: 25

VAD/CNG: no

Echo cancel: voice (default)

DSCP RTP: 0

DSCP SIG: 0

RTCP period: 0

RTCP control: 0

RTP loss timeout: off

DTMF MODE: RFC2833

DTMF PType: 101

DTMF MIMETYPE: application/dtmf

CCI: off

Redirect (302): disabled

REFER: disabled

Session Expires: 1800

Min SE: 90

Refresher: uac

Rport: disabled

Options: disabled:0

FAX-detect: no detecting

FAX-mode: none

VBD: disabled

Jitter buffer adaptive mode

minimum size: 0 ms

initial size: 0 ms

maximum size: 200 ms

Summary of Contents for SMG-1016M


























































































































































































































































































































































































































































Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands

ELTEX SMG-1016M, Operation Manual

Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands