ELTEX SMG-1016M Operation Manual Download Page 5

Page: 5 / 441

SMG Digital Gateway

–

SMG connection method example for operation in combined mode

–

Appendix. Voice messages and music on hold (MOH).

Version 1.10

V.2.12.01

20.05.2013

Added:

–

Appendix 'Guidelines for SMG operation in public network'

Version 1.9

V.2.12.01

1.04.2013

Added:

–

Network services section — Configuration of NTP, DHCP, SNMP parameters and allowed
address list in separate section

–

Assigning system parameters

–

E1 channel monitoring

–

VoIP submodule monitoring

–

Trunk direction configuration

–

Original CdPN and RedirPN modifiers

–

Q.931 timer configuration

–

Device access restriction settings

–

Incoming or outgoing communication restriction for subscriber

–

Configuration of network interface for signal SIP messages and voice traffic reception and
transmission

Version 1.8

V.2.11.02

09.01.2013

Added:

–

Expanded list of E1 stream monitoring parameters

–

SFP module monitoring

–

Fault state monitoring

–

Alarm events list

–

MTP3 (DPC-MTP3) destination point code function support

–

ISUP (DPC- ISUP) destination point code function support

–

Dial plan wildcard search

–

NAT (comedia mode) for SIP operation via NAT

–

VPN/PPTP interface configuration

–

Creation of list of allowed addresses used for device connection

–

Trace filters:

–

restriction on number of simultaneous calls for subscriber

Version 1.7

V.2.10.04

20.09.2012

Added:

–

Modifier table configuration in separate menu

–

Modifier selection from table during cdr configuration

–

Modifier selection from table during pbx record configuration

–

Modifier selection from table during RADIUS record configuration

–

Modifier selection from table during trunk group configuration

Version 1.6

V.2.10.02

20.08.2012

Added:

–

Fail2ban settings

–

CPU utilization monitoring

–

Modifier operation examples

–

Configuration of SIP interface registration parameters

–

View list of addresses issued via DHCP

–

STUN server settings

–

Digest authorization settings

–

SIP subscribers group editing

Version 1.5

V.2.9.05

20.03.2012

Added:

–

РBX profiles for SIP subscribers

–

Additional settings for CDRs (redirection tags, redirecting number)

–

Separate interface for RADIUS message exchange

Version 1.4

V.2.9.03

28.12.2011

Added:

–

Maximum number of trunk groups and SIP interfaces increased up to 64

–

SNMP trap configuration

–

DHCP server management

–

IP-MAC address binding

–

Apply/confirm switch settings w/o gateway reboot

–

Apply/confirm VLAN settings w/o gateway reboot

–

Subscriber number availability check against configured SIP subscriber database

–

Availability check for routing by number

–

Ability to read CDR from local drives

–

Reception monitoring for media traffic coming from the specific IP

Version 1.3

V.2.1.01

3.11.2011

Added:

–

CDR configuration

Version 1.2

V.2.1.01

21.10.2011

Bugfixes

Version 1.1

V.2.0.10

10.10.2011

Added:

–

DHCP server settings

–

Received/transferred signal volume settings

Version 1.0

V.2.0.10

12.09.2011

First edition

Summary of Contents for SMG-1016M


























































































































































































































































































































































































































































Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands

ELTEX SMG-1016M, Operation Manual

Search results

Summary of Contents for SMG-1016M

Reviews:

Related manuals for SMG-1016M

Brands by name

Popular brands