MANUAL ELDES ESIM264 V3.2
MANUAL ELDES ESIM264 V3.2
12. ARMING AND DISARMING
The system features the following methods to carry out arming and disarming process:
• Free of charge phone call.
• SMS text message.
• EKB2/EKB3 keypad and user code.
• iButton key.
• EWK1/EWK2 wireless keyfob.
• Arm-Disarm by Zone.
• EGR100 middle-ware.
The system arms/disarms the partitions that the listed user phone number, EKB2/EKB3 keypad and user code, iButton key, EWK1 wireless
keyfob or zone, set up for Arm-Disarm by Zone method, are assigned to. For example, if User 1 phone number is assigned to Partition 0, the
user will be able to arm/disarm Partition 0 by a single phone call to the system (see
23. PARTITIONS
).
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message. For more details on SMS
text message regarding system arming/disarming and how to manage it, please refer to
12.9. Disabling and Enabling Arm/Disarm
Notifications
.
The system will allow to arm the system if the following system faults are present (see
29. INDICATION OF SYSTEM FAULTS
):
• Mains power is lost.
• Low battery.
• Battery failed.
• Date/time not set.
• GSM connection failed.
In case of violated zone/tamper presence when attempting to arm the system by free of charge phone call, SMS text message, iButton key
and Arm-Disarm by Zone method, the system will reply with SMS text message containing violated zone/tamper number. Due to securi-
ty reasons it is highly recommended to restore the violated zone/tamper before arming the system. For more details on how to arm the
system regardless of the violated zone presence, please refer to
14.6. Zone Attributes
and
14.7. Bypassing and Activating Zones
.
Once a user phone number is listed, the system ignores any incoming calls and SMS text messages from a non-listed phone number as well
as it rejects the SMS text messages containing wrong SMS password even from a listed user phone number. For more details regarding
arming/disarming the system from a non-listed phone number, please refer to
8.1. System Control from any Phone Number.
12.1. Free of Charge Phone Call
To arm and disarm the system, dial the system‘s phone number from any of 5 available user phone numbers (see
8. USER
PHONE NUMBERS
for user phone number management). The phone call is free charge as the system rejects it and carries out
arming/disarming procedure afterwards. When arming – the system rejects the phone call after 2 rings, when disarming – the
system rejects the phone call immediately. If there is more than one listed user dialling to the system at the same time, the
system will accept the incoming call from the user who was the first to dial while other user (-s) will be ignored.
The system will arm/disarm the partition corresponding to the one that the user phone number is assigned to. For more details on how to
set user phone number partition, please refer to
23.2. User Phone Number Partition.
CALL
User
ESIM264
30
12.2. SMS Text Message
SMS
To arm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user
phone numbers (see
8. USER PHONE NUMBERS
for user phone number management). When the SMS text message for arm-
ing is sent to the system’s phone number, the system will proceed as follows:
• Non-partitioned system:
• If ready (no violated zone/tamper), the system will arm.
• If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number.
• Partitioned system:
• If all partitions are disarmed ready (no violated zone/tamper), the system will arm them.
• If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready par-
tition (-s) and skip the unready one (-s). The system will then send an SMS text message, containing a list of violated
zones/tampers, to user phone number that the system arming was initiated from.
• If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions
and skip the armed ones.
Arm the system
SMS text message content:
ssss_ARMp
or
ssss_ARMp,p
Value:
ssss
– 4-digit SMS password;
p
– partition number, range – [
1
– Partition 0,
2
– Partition 1].
Example:
1111_ARM1
SMS
User
ESIM264
31
To disarm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user phone numbers:
Disarm the system
SMS text message content:
ssss_DISARMp
or
ssss_DISARMp,p
Value:
ssss –
4-digit SMS password;
p
– partition number, range - [
1
– Partition 0,
2
– Partition 1].
Example:
1111_DISARM1,2
SMS
User
ESIM264
32
Regardless of the partition a user phone number is assigned to, the user will be able arm/disarm by SMS text message method either Par-
tition 0 , Partition 1 or both partitions simultaneously.
12.3. EKB2 Keypad and User Code
EKB2
READY
message displayed in the home screen view by EKB2 keypad indicates that no violated zones and/or tampers are pres-
ent, therefore the system can be armed. If the message is displayed as
NOT READY
, the user must restore all violated zones
and tampers before arming the system. Alternatively, the violated zones can be bypassed (see
14.7. Bypassing and Activat-
ing Zones
), disabled (see
14.9. Disabling and Enabling Zones
) or a Force attribute enabled (see
14.6. Zone Attributes
).
To arm the system by EKB2 keypad, enter any out of 30 available 4-digit user codes using the number keys on the keypad (see
10. USER CODES
for user code management).
By default when a valid user code is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps and
the keypad will display
icon next to the countdown timer. When the system is successfully armed, the keypad will display
icon for 5 seconds and switch to home screen view.
