56
User Manual
MN04200002E
Effective January 2016
C441 Ethernet module user manual
(C441R, C441T, C441U, C441V)
EATON
www.eaton.com
7.4 Register Definition for the S611 Soft Starter
Table 101. Register Definition for the S611 Soft Starter
Start
Coil
Register
Read/
Write
Name
Description (Units)
1
1
R
Field Inputs
A Bitfield Representing the Input Points.
Bit = Description
0 = Input 1
1 = Input 2
2 = Input 3
3 = Input 4
-
2
R
Control Voltage Adapter Source Voltage. ( mV )
- 3
R Ambient
Temperature
Device ambient temperature as mea-
sured from the PCB. ( ºC )
- 4
R/W
Max
Board
Temperature
The maximum board temperature experi-
enced since manufacturing. ( ºC )
65 5
R Dip
Switch
Value
A bit field representing the present state
of the dip switches.
- 6
R Configuration
CRC
A CRC value calculated over the non-
volatile data present.
-
7
R/W
Serial Number
32 bit Com Adapter Device Serial
Number.
-
9
R
Firmware Rev
Com Adapter Firmware Rev.
-
11
R/W
Hardware Rev
Com Adapter Hardware Rev.
1601 101
R/W Field
Relay
Outputs
A Bitfield Representing the Output
Points.
Bit = Description
0 = Output 1
1 = Output 2
- 102 R/W
Field
Inputs
Debounce
Array of debounce values. A debounce
value exists for each input. The
debounce applies to both rising and fall-
ing edge. ( milliseconds )
- 110 R/W
Modbus
TCP
Com Timeout
Communication Timeout for Modbus
TCP. 0 = Disable. ( milliseconds )
1761 111
R/W Field
Relay
Fault Action
When a communication fault occurs
the relays can execute two types of
behavior. The behavior is selected on a
per bit basis.
Bit = Description
0 = Relay 1
1 = Relay 2
Bit Value = Description
0 = Apply Fault Value
1 = No Change
1777 112
R/W Field
Relay
Fault State
Communication fault value to be
applied. A bitfield where each bit
defines an output point.
Bit Value = Description
0 = Turn Relay Off
1 = Turn Relay On
1793
113
R/W
Field Relay Idle
Action
When a communication idle state occurs
the relays can execute two types of
behavior. The behavior is selected on a
per bit basis.
Bit = Description
0 = Relay 1
1 = Relay 2
Bit Value = Description
0 = Apply Idle Value
1 = No Change
1809
114
R/W
Field Relay Idle
State
Communication idle value to be applied.
A bitfield where each bit defines an
output point.
Bit Value = Description
0 = Turn Relay Off
1 = Turn Relay On
Table 101. Register Definition for the S611 Soft Starter (Cont.)
Start
Coil
Register
Read/
Write
Name
Description (Units)
-
143
R
Method of IP
Allocation
The Method Used to Allocate an IP
Address:
0 - DHCP
1 - Upper three octets from NV and
lower octet selected by the dip switch
setting.
2 - Full address taken from NV Memory.
3 - Restore (hardcoded 192.168.1.254).
- 144 R Present
Ethernet IP
Address
The active IP address being used on the
network.
- 146 R Present
Ethernet Subnet
Mask
The active subnet mask IP address being
used on the network.
- 148 R Present
Ethernet
Default
Gateway
The active default gateway IP address
being used on the network.
- 150 R/W
Stored
Ethernet
IP Address
The IP address used in the NV address
select configuration.
- 152 R/W
Stored
Ethernet
Subnet Mask
The IP subnet mask used in the NV
address select configuration.
- 154 R/W
Stored
Ethernet
Default
Gateway
The IP default gateway used in the NV
address select configuration.
- 156 R/W
Ethernet
MAC
Address
-
- 159 R/W
Modbus
Com
Timeout
Communication Timeout for Modbus.
0 = Disable. ( milliseconds )
- 160 R/W
Modbus
TX
mode
Selects the Modbus Mode.
0 - RTU
1 - ASCII
- 161 R/W
Modbus
Baud
Rate
Selects the Modbus Baud Rate.
0 - 19.2kb
1 - 9.6kb
2 - 57.6kb
3 - 115.2kb
- 162 R/W
Modbus
Address
Modbus address loaded at startup.
- 163 R/W
Modbus
Parity
and Stop Bits
Selects the Modbus UART Parity and
Stop Bits.
0 - Even/One Stop Bit
1 - Odd/One Stop Bit
2 - None/Two Stop Bits
3 - Even/Two Stop Bits
4 - Odd/Two Stop Bits
5 - None/One Stop Bit
3201
201
R
Intercom Status Present State of the Intercom Link.
Bit - Status
0 - Connected fully. No error messages.
1 - A message fault occurred.
2 - Devices are married. Target is identi-
fied and correct.
3 - A basic connection is established.
4001 251
R/W Motor
Ctrl
Idle Loss Act
Disable
When this value is TRUE the motor state
will be unchanged after a communica-
tion idle event. A FALSE value will
cause the Motor Control Communication
Idle Value to be applied on a com idle
event.
4017
252
R/W
Motor Ctrl Com
Idle Action Val
Action to execute when a communica-
tion loss event occurs.
0 = Ignore (No Change)
1 = Stop
4033 253
R/W Motor
Ctrl
Com Loss Act
Disable
When this value is TRUE the motor state
will be unchanged after a communica-
tion loss event. A FALSE value will
cause the Motor Control Communication
Loss Value to be applied on a com loss.
4049
254
R/W
Motor Ctrl Com
Loss Action Val
Action to execute when a communica-
tion loss event occurs.
0 = Ignore (No Change)
1 = Stop
