manualshive.com logo in svg

Eaton C441R, User Manual, Page: 52 / 68

Share
Download
Eaton C441R User Manual Download Page 52

52

User Manual 

MN04200002E

Effective January 2016

C441 Ethernet module user manual 

(C441R, C441T, C441U, C441V) 

  

EATON

 www.eaton.com

Table 99. Registers Available with C441 Motor Insight (Cont.)

Start 
Coil

Register

Read/
Write Name

Description (Units)

- 327  R Remaining 

Underload 
Trip Restart 
Delay 

Load Fault - Time to Restart ( sec ) 

- 328  R/W 

Run 

Time 

Hours 

Motor Run Time in hours (resettable) ( hr ) 

- 

329 

R 

Start Count 

Start Count (Resettable) 

- 

330 

R 

Trip Reason 

0x0001 - Restart Attempts Exceeded 
0x0002 - Relay Turned Off (Network/UI) 
0x0004 - Contactor Failure 
0x0008 - Under Current Trip 
0x0010 - Overload Trip 
0x0020 - GND Fault Trip 
0x0040 - Current Unbalance Trip 
0x0080 - Current Single Phase 
0x0100 - Reserved (0) 
0x0200 - High Power Trip 
0x0400 - Over Voltage Trip 
0x0800 - Under Voltage Trip 
0x1000 - Voltage Unbalance Trip 
0x2000 - Over Current Trip 
0x4000 - Low Power Trip 
0x8000 - Phase Reversal Trip 

- 331  R Overload 

Status 

Overload Status 
- 0x0001: Overload Trip 
- 0x0002: Ground Fault Trip 
- 0x0004: High Power Trip 
- 0x0080: Relay Closed 

- 

332 

R 

Error Code 

Warning/Alarm Indications 
0x0001 (1) - Low Voltage Warning 
0x0002 (2) - High Voltage Warning          
0x0004 (4) - Voltage Unbalance Warning 
0x0008 (8) - Low Power Warning  
0x0010 (16) - Reverse Phase Warning 
0x0020 (32) - Current Unbalance Warning 
0x0040 (64) - Voltage Single Phase 
Warning 
0x0080 (128) - Current Single Phase 
Warning 
0x0100 (256) - GND Fault Warning

- 333  R C441 

DSP 

FW Version 

C441 DSP Firmware Version 

- 334  R UI 

Firmware 

Version 

User Interface Firmware Version 

- 

335 

R/W 

C441 Unit ID  Unit ID 

0x00BA (186) - C441BA 
0x00BB (187) - C441BB 
0x00CA (202) - C441CA 
0x00CB (203) - C441CB 
0x00DA (218) - C441DA 
0x00DB (219) - C441DB 
0x00EA (234) - C4410109(x) 
0x00EB (235) - C4410590(x) 

5361 336 

R 

Aux 

Relay 

Trip Reason 

0x0002 - Relay Turned Off (Network/UI) 
0x0004 - Contactor Failure 
0x0008 - Under Current Trip 
0x0010 - Overload Trip 
0x0020 - GND Fault Trip 
0x0040 - Current Unbalance Trip 
0x0080 - Current Single Phase 
0x0100 - Mains Freq Fault 
0x0200 - High Power Trip 
0x0400 - Over Voltage Trip 
0x0800 - Under Voltage Trip 
0x1000 - Voltage Unbalance Trip 
0x2000 - Over Current Trip 
0x4000 - Low Power Trip 
0x8000 - Phase Reversal Trip 

Table 99. Registers Available with C441 Motor Insight (Cont.)

Start 
Coil

Register

Read/
Write Name

Description (Units)

- 400  R/W 

Command 
register 

0x0066 - Clear Motor Run Hours 
0x0077 - Clear Fault Queue 1 
0x0078 - Clear Fault Queue 
0x0088 - Network watchdog enable 
0x0099 - Network watchdog disable 
0x00AA - Reset Relay 
0x00BB - Clear Motor Start Count 
0x00CC - Force Ground Fault 
0x00DD - Fault Relay OFF 
0x00EE  - Reset Auxiliary Relay (120 Vac 
Control Power models only) 

- 401  R/W 

Motor 
Control 

- 

- 402  R/W 

Configuration 
Reset 

1 = Soft Reset (equivalent to a power 
cycle) 
2 = Factory Reset 

- 

403 

R/W 

CT Multiplier  For 90 Amp Units: 1-4, number of conduc-

tors through CT. 
For 9 Amp Units: 1-2, number of conduc-
tors through CT; 
For 9 Amp Units, CT multipliers: 3 (150:5), 
4 (300:5), 5 (600:5) 

- 404  R/W 

Ground 

Fault 

Pick-up Level 

Ground Fault Pick-up Level ( x0.01A ) 

- 405  R/W 

Under 
Current Pick-
up Level 

Under Current Pick-up Level ( % ) 

- 406  R/W 

Low 

Power 

Pick-up Level 

Low Power Pick-up Level ( x0.01kW ) 

- 

407 

R/W 

Overload FLA  Motor Full Load Current ( x0.01A ) 

- 408  R/W 

Current 
Unbalance 
Pick-up Level 

Current Unbalance Pick-up Level ( % ) 

- 409  R/W 

Overload 

Trip 

Class 

Overload Trip Class 

- 410  R/W 

Under 
Voltage Pick-
up Level 

Under Voltage Pick-up Level ( V ) 

- 411  R/W 

Over 

Voltage 

Pick-up Level 

Over Voltage Pick-up Level ( V ) 

- 412  R/W 

Voltage 
Unbalance 
Pick-up Level 

Voltage Unbalance Pick-up Level ( % ) 

- 413  R/W 

Jam 

Pick-up 

Level 

Jam Pick-up Level ( % ) 

- 

414 

R/W 

High KW Trip 
limit 

High Power Pick-up Level ( x0.01kW ) 

- 

415 

R/W 

Phase Order 

Phase Order 
- 0 (Trip Disabled) 
- 1 ACB 
- 2 ABC 

- 416  R/W 

Supply 

Fault 

Hold-off Time 

Restart Delay ( sec ) 

- 417  R/W 

Motor 

Fault 

Hold-off Time 

Motor Fault Reset Delay ( min ) 

- 418  R/W 

Load 

Fault 

Hold-off Time 

Load Fault Reset Delay ( min ) 

- 419  R/W 

Load 

Fault 

Number of 
Restarts 

Load Fault Number of Reset Attempts 
0: Manual 
1-4 
5: Automatic 

- 420  R/W 

Motor 

Fault 

Number of 
Restarts 

Motor Fault Number of Attempts: 
0: Manual 
1-4 
5: Automatic 

- 421  R/W 

Ground 

Fault 

Trip Delay 

Ground Fault Pickup Delay ( sec ) 

- 422  R/W 

Under 
Current Trip 
Delay 

Under Current Trip Delay ( sec ) 

- 423  R/W 

Low 

Power 

Trip Delay 

Low Power Trip Delay ( sec ) 

- 424  R/W 

Jam 

Trip 

Delay 

Jam Trip Delay ( sec ) 

Summary of Contents for C441R





































































Reviews:

No comments