manualshive.com logo in svg

Dodge 2011 Grand Caravan, Owner'S Manual

Looking for a user manual for your Dodge 2011 Grand Caravan? Look no further! Download the comprehensive manual for free from manualshive.com, providing you with all the essential information you need to operate and maintain your vehicle. Simply click the link and get instant access to the manual.

Share
Download
background image

WARNING!

Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.

5. Remove the wheel lug nuts, for vehicles with wheel
covers, remove the cover from the wheel by hand. Do not
pry the wheel cover off. Then pull the wheel off the hub.

6. Install the compact spare tire. Lightly tighten the lug
nuts.

WARNING!

To avoid the risk of forcing the vehicle off the jack,
do not tighten the lug nuts fully until the vehicle has
been lowered.

NOTE:

•

Do not install the wheel cover on the compact spare.

•

Do not use a hammer or force to install the wheel
covers.

7. Lower the vehicle by turning the jack screw to the left.

8. Finish tightening the lug nuts. Push down on the
wrench while tightening for increased leverage. Alternate
lug nuts until each nut has been tightened twice. The
correct wheel nut tightness is 102 ft lbs (138 N·m). If in
doubt about the correct tightness, have them checked
with a torque wrench by your authorized dealer or at a
service station.

9. Lower the jack to its fully-closed position.

452

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Brand: DANA Pages: 42
dallara F305 Manual preview
F305
Brand: dallara Pages: 37
Yakima BOA Installation Instructions Manual preview
BOA
Brand: Yakima Pages: 8
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Brand: Jacob Jensen Pages: 28
ECS Electronics CR-066-BHU Manual preview
CR-066-BHU
Brand: ECS Electronics Pages: 16
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Brand: Mazda Pages: 400
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Brand: Wagan Pages: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Brand: Chevrolet Pages: 50
Jeep Cherokee 2000 Service Manual preview
Cherokee 2000
Brand: Jeep Pages: 1528
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Brand: Jaeger Pages: 17
Ranger design 1525-NS Installation Manual preview
1525-NS
Brand: Ranger design Pages: 22
National Cycle Quantum hardcoated N30216 Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30216
Brand: National Cycle Pages: 3
METRON PC05T User Manual preview
PC05T
Brand: METRON Pages: 4
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
Ford FUSION 2014 Owner'S Manual preview
FUSION 2014
Brand: Ford Pages: 458
Elinchrom ELB 1200 User Manual preview
ELB 1200
Brand: Elinchrom Pages: 101
Gator GT700SD User Manual preview
GT700SD
Brand: Gator Pages: 6
F.lli Menabo CROSS 2 Assembly Instructions Manual preview
CROSS 2
Brand: F.lli Menabo Pages: 16

Brands by name

Popular brands

Load more brands