Dodge 2011 Grand Caravan Owner'S Manual Download Page 452

Page: 452 / 562

2. There are two jack engagement locations on each side
of the vehicle body. These locations are on the sill flange
of the vehicle body.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated.

Rear jack locations are between a pair of down-facing
tabs on the sill flange of the vehicle side body.

Front jack location is on the sill flange of the vehicle body
and is located 6 in (150 mm) from door edge.

Jack Location

Rear Jacking Location

450

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands