Dodge 2011 Grand Caravan Owner'S Manual Download Page 451

Page: 451 / 562

WARNING! (Continued)

•

If working on or near a roadway, be extremely
careful of motor traffic.

•

To assure that spare tires, flat or inflated, are
securely stowed, spares must be stowed with the
valve stem facing the ground.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.

NOTE:

Refer to the “Compact Spare Tire” section of

“Tires – General Information” for information about the
spare tire, its use, and operation.

1. Loosen (but do not remove) the wheel lug nuts by
turning them to the left one turn while the wheel is still
on the ground.

Jack Warning Label

WHAT TO DO IN EMERGENCIES

449

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands