Dodge 2011 Grand Caravan Owner'S Manual Download Page 202 | Manualshive

Page: 202 / 562

background image

•

After training a HomeLink

威

channel, if the garage

door does not operate with HomeLink

威

and the ga-

rage door opener was manufactured after 1995, the
garage door opener may have a rolling code. If so,
proceed to Step 5 “Programming A Rolling Code
System.”

4. Press and hold the just-trained HomeLink

威

button

and observe the indicator light.

If the indicator light stays on constantly, programming is
complete and the garage door (or device) should activate
when the HomeLink

威

button is pressed.

If the indicator light blinks rapidly for two seconds and
then turns to a constant light, proceed to “Programming
A Rolling Code System.”

5. Programming A Rolling Code

At the garage door opener motor (in the garage), locate
the “Learn” or “Training” button.

This can usually be found where the hanging antenna
wire is attached to the garage door opener motor. It is
NOT the button normally used to open and close the
door.

Training The Garage Door Opener

1 — Door Opener
2 — Training Button

200

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
200
201
202
203
204
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: TATA Motors Pages: 94

Brand: GÄN Pages: 24

Brand: Vauxhall Pages: 2

Brand: CITROËN Pages: 301

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Calispace Ocean 80

Brand: Calitop Pages: 5

Brand: mtf TRANSPORT SYSTEM Pages: 9

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: Anker Technology Pages: 8

Brand: Mitsubishi Pages: 362

nERGY ETSA200R-PA

Brand: Soundoff Signal Pages: 3

Brand: Truma Pages: 10

Brand: Scosche Pages: 12

Brand: Arrista Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands