Dodge 2011 Grand Caravan Owner'S Manual Download Page 72 | Manualshive

Page: 72 / 562

background image

Enhanced Seat Belt Use Reminder System
(BeltAlert

姞

)

BeltAlert

威

is a feature intended to remind the driver and

front passenger (if equipped with front passenger
BeltAlert

威

) to fasten their seat belts. If the driver or front

seat passenger is unbelted, the Seat Belt Reminder Light
will turn on and remain on until both front seat belts are
fastened.

The BeltAlert

威

warning sequence begins within 60 sec-

onds of the vehicle speed over 5 mph (8 km/h), by
blinking the Seat Belt Reminder Light and sounding an
intermittent chime. Once the sequence starts, it will
continue for 96 seconds or until the respective seat belts
are fastened. After the sequence completes, the Seat Belt
Reminder Light remains illuminated until the respective
seat belts are fastened. The driver should instruct all
other occupants to fasten their seat belts. If a front seat
belt is unbuckled while traveling at speeds greater than

5 mph (8 km/h), BeltAlert

威

will chime once and illumi-

nate the Seat Belt Reminder Light, then will proceed to
the 96 second warning sequence.

The front passenger seat BeltAlert

威

is not active when the

front passenger seat is unoccupied. BeltAlert

威

may be

triggered when an animal or heavy object is on the front
passenger seat or when the seat is folded flat (if
equipped). It is recommended that pets be restrained in
the rear seat in pet harnesses or pet carriers that are
secured by seat belts, and cargo is properly stowed.

BeltAlert

威

can be enabled or disabled by your authorized

dealer or by following these steps:

NOTE:

The following steps must occur within the first

60 seconds of the ignition switch being cycled to the
ON/RUN position. Chrysler Group LLC does not recom-
mend deactivating BeltAlert

威

.

70

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
70
71
72
73
74
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: Neuspeed Pages: 2

Brand: Sirius Satellite Radio Pages: 8

Brand: Ford Pages: 368

Brand: Audiovox Pages: 24

Brand: Mercedes-Benz Pages: 2

Brand: Westin Pages: 2

Brand: mtf TRANSPORT SYSTEM Pages: 9

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Mobility Networks Pages: 52

Brand: Elinchrom Pages: 101

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

Brand: ROADGEAR Pages: 2

Brand: KLAUS Multiparking Pages: 72

Brand: QA1 Pages: 3

Brand: Seat Pages: 300

Brand: Mercedes-Benz Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands