Dodge 2011 Grand Caravan Owner'S Manual Download Page 71

Page: 71 / 562

4. The AHR front soft foam and trim half should lock
into the back decorative plastic half.

NOTE:

•

If you have difficulties or problems resetting the
Active Head Restraints, see an authorized dealer.

•

For safety reasons, have the Active Head Restraints
checked by a qualified specialist at an authorized
dealer.

3 — Final Downward Movement To Engage Locking Mecha-

nism

AHR In Reset Position

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands