manualshive.com logo in svg

Dodge 2011 Grand Caravan, Owner'S Manual

Looking for a user manual for your Dodge 2011 Grand Caravan? Look no further! Download the comprehensive manual for free from manualshive.com, providing you with all the essential information you need to operate and maintain your vehicle. Simply click the link and get instant access to the manual.

Share
Download
background image

NOTE:

Remember that everything put into or on the

trailer adds to the load on your vehicle. Also, additional
factory-installed options, or authorized dealer-installed
options, must be considered as part of the total load on
your vehicle. Refer to the “Tire Safety Information/Tire
and Loading Information Placard” in “Starting and Op-
erating” for the maximum combined weight of occupants
and cargo for your vehicle.

Towing Requirements

To promote proper break-in of your new vehicle drive-
train components, the following guidelines are recom-
mended:

CAUTION!

•

Do not tow a trailer at all during the first 500 miles
(805 km) the new vehicle is driven. The engine,
axle or other parts could be damaged.

(Continued)

CAUTION! (Continued)

•

Then, during the first 500 miles (805 km) that a
trailer is towed, do not drive over 50 mph
(80 km/h) and do not make starts at full throttle.
This helps the engine and other parts of the
vehicle wear in at the heavier loads.

Perform the maintenance listed in the “Maintenance
Schedule.” Refer to “Maintenance Schedule” for further
information. When towing a trailer, never exceed the
GAWR or GCWR ratings.

5

STARTING AND OPERATING

429

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Pacbrake 10475 Installation Manual preview
10475
Brand: Pacbrake Pages: 9
Camcar 40108 Mounting Instructions preview
40108
Brand: Camcar Pages: 6
ABL eMH3 Quick Start Manual preview
eMH3
Brand: ABL Pages: 4
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Brand: Bestop Pages: 7
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Brand: Safe Fleet Pages: 11
Camec 042374 User Manual preview
042374
Brand: Camec Pages: 19
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Brand: minnid Pages: 44
Dodge 8W-30 Wiring Diagram preview
8W-30
Brand: Dodge Pages: 24
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Brand: Ford Pages: 368
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Buick 1988 Riviera Owner'S Manual preview
1988 Riviera
Brand: Buick Pages: 161
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Brand: Jaeger Pages: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Brand: ATS Pages: 12
Magneti Marelli AC911 Installation Instruction preview
AC911
Brand: Magneti Marelli Pages: 3
G-Tech Pro Competition User Manual preview
Pro Competition
Brand: G-Tech Pages: 180
Yakima SUPDawg Manual preview
SUPDawg
Brand: Yakima Pages: 10
Thule 1325 Kit Instructions Manual preview
1325 Kit
Brand: Thule Pages: 8
v.link VL2-CIC Manual preview
VL2-CIC
Brand: v.link Pages: 15

Brands by name

Popular brands

Load more brands