Dodge 2011 Grand Caravan Owner'S Manual Download Page 214 | Manualshive

Page: 214 / 562

background image

CAUTION! (Continued)

•

Power outlets are designed for accessory plugs
only. Do not hang any type of accessory or acces-
sory bracket from the plug. Improper use of the
power outlet can cause damage.

POWER INVERTER — IF EQUIPPED

A 110 Volt, 150 Watt inverter outlet (if equipped) converts
DC current to AC current, and is located on the left rear
trim panel immediately behind the second row left
passenger seat.

The power inverter switch is located on the instrument
panel below the climate controls.

Power Inverter Outlet

212

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
212
213
214
215
216
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: ZAPTEC Pages: 240

Brand: AAMP of America Pages: 6

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: Whispbar Pages: 15

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Beper Pages: 52

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: Ranger design Pages: 24

Brand: APS Pages: 3

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Brand: Rhino-Rack Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands