Dodge 2011 Grand Caravan Owner'S Manual Download Page 515

Page: 515 / 562

Chassis

Component

Fluid, Lubricant, or Genuine Part

Automatic Transmission

MOPAR

威

ATF+4

威

Automatic Transmission Fluid or equivalent licensed

ATF+4

威

product.

Brake Master Cylinder

MOPAR

威

DOT 3 and SAE J1703 should be used or equivalent. If DOT 3

brake fluid is not available, then DOT 4 is acceptable. Use only recom-
mended brake fluids.

Power Steering Reservoir

MOPAR

威

Power Steering Fluid +4, MOPAR

威

ATF+4

威

Automatic Trans-

mission Fluid or equivalent licensed ATF+4

威

product.

MAINTAINING YOUR VEHICLE

513

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands