Dodge 2011 Grand Caravan Owner'S Manual Download Page 142

Page: 142 / 562

NOTE:

Seat will not stow in the storage bin unless the

armrests are raised.

4. Slide the storage bin locking mechanism to the
“LOCK” position and then pull up on the storage bin
latch to open the cover.

5. Pull upward on the seatback recliner lever located on
the outboard side of the seat.

Storage Bin Cover Lock Release

Seatback Recliner Lever, Seat Tumble, And Head

Restraint Fold Lever

140

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands