Dodge 2011 Grand Caravan Owner'S Manual Download Page 197

Page: 197 / 562

The door will slowly rotate to the full open position.

From this position, the door can be fully closed or, by
rotating upward about 3/4 of the way and releasing,
positioned for conversation mirror use.

NOTE:

From the “conversation mirror” position, the

door can only be closed.

To return to the full open position, the door must first be
closed and then opened by pressing the latch again to
release.

Full Open Position

Conversation Mirror Position

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

195

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands