Dodge 2011 Grand Caravan Owner'S Manual Download Page 464

Page: 464 / 562

3. Turn the ignition switch to the ON/RUN position
without starting the engine.

4. Press and maintain firm pressure on the brake pedal.

5. Using a small screwdriver or similar small, push and
hold the override release lever forward.

6. Move the shift lever into the NEUTRAL position.

7. The vehicle may then be started in the NEUTRAL
position.

8. Reinstall the shift lever override access cover.

TOWING A DISABLED VEHICLE

Towing Condition

Wheels OFF the Ground

ALL MODELS

Flat Tow

NONE

If transmission is operable:

•

Transmission in

NEUTRAL

•

25 mph (40 km/h)

max

speed

•

15 miles (24 km)

max

distance

Wheel lift

Rear

Front

Flatbed

ALL

BEST METHOD

462

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands