Dodge 2011 Grand Caravan Owner'S Manual Download Page 171

Page: 171 / 562

To activate the Halo lights, rotate the Halo
switch control upward or downward to in-
crease or decrease the lighting.

Multifunction Lever

The multifunction lever is located on the left side of the
steering column.

The multifunction lever controls the:

•

Turn Signals

Halo Control

Multifunction Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

169

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands

Dodge 2011 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2011 Grand Caravan

Reviews:

Related manuals for 2011 Grand Caravan

Brands by name

Popular brands