DIMAT TPU-1 Installation And Comissioning Manual Download Page 36

Page: 36 / 69

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

36/69

5.5.1

Characteristics of the management computer



Hardware

Pentium III 550 MHz processor or higher.

512 Mbytes of RAM memory.

A LAN module with 10/100Base-TX or 100Base-FX interface.

1 Mbyte SVGA graphic adapter.

A mouse.



Software

Microsoft Windows XP Service Pack 2 version or Microsoft Windows 7 or Microsoft

Windows 10 operating system.

TCP/IP protocol.

Microsoft Internet Explorer v 6.0 web browser or higher.

JAVA virtual machine (Sun Microsystems) version 1.7 or higher.

5.5.2

Connections

10/100Base-TX LAN interface

The TPU-1 terminal can have a 10/100Base-TX LAN interface, which allows it to be

integrated into any network (LAN) that uses this interface. The connector is on the front of

the MWTU module and is a female 8-pin RJ-45.

The cable used to carry out the connection between the terminal and the computer must be

an unshielded twisted pair category five cable (UTP-5) with 8-pin RJ-45 connectors.

Table 2 shows the use of each one of the pins of the RJ-45 connector, as well as the pair it

belongs to according to ANSI/TIA/EIA-568-A standard, in the 10/100Base-TX LAN interface.

Table 2 Signals of the RJ-45 connector in the 10/100Base-TX LAN interface

Summary of Contents for TPU-1






































































Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands

DIMAT TPU-1, Installation And Comissioning Manual

Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands