DIMAT TPU-1 Installation And Comissioning Manual Download Page 66

Page: 66 / 69

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

66/69

APPENDIX D

OPTIONAL LCD DISPLAY

In order to monitor certain parameters from the front plate of the terminal, without having to

access the corresponding option of the Management System, the TPU-1 Universal

Teleprotection terminal can be supplied with an LCD display, on demand.

As can be seen in Figure 51, the display has an associated push-button.

Figure 51 Optional LCD display

The LCD display is activated when the push-button is pressed, and automatically goes out

when neither is pressed within 10 minutes. This is in order to guarantee a longer life of the

display.

Once the display is activated, the push-button must be pressed again to display the

information screen.

All the screens display the date (day-month-year) and UTC time (hour-minutes-seconds) at

all times, except for the main screen.

Summary of Contents for TPU-1






































































Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands

DIMAT TPU-1, Installation And Comissioning Manual

Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands