DIMAT TPU-1 Installation And Comissioning Manual Download Page 28

Page: 28 / 69

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

28/69

4.3.6

IATU and IBTU modules

The line interface modules for analog channel allow the transmission of teleprotection

signals by means of 4 wire connections, for operation by single tone (IATU/IBTU) or dual

tone (IBTU). Figure 23 shows a front view of an analog line interface (IATU or IBTU)

module. As can be seen in the figure, the analog line interface module has a plug-in

connector.

The earth connection of the cable must be connected to the upper fixing screw. Make sure

that the module is completely fixed to the chassis.

Figure 23

Analog

line interface module (IATU or IBTU) connector

The auxiliary relay is configurable from the Management System for command transmission

signalling, command output or alarm and, if be the case, unblocking. In the case of alarm, the

relay will act for one or more of the following causes:

RTC synchronization failure,

Telemeasuring failure, IEC 61850 link failure, Power-supply failure, Main module failure,

Module failure in slot (no.), Manual blocking (analog and digital), Automatic test failure (analog

and digital), Incorrect SIC security identification code (digital), Loss of synchronism (digital),

Incorrect identification code (digital), BER alarm (digital), Remote Alarm Indication (digital

IOCT type), Loss of signal (digital IOCT type), Reception blocking (analog), Error of reception

(analog), Low Signal/Noise ratio (analog), Signal loss (analog), Low guard-signal level/Excess

guard-signal level (analog), MTD alarm (IP interface), CDV alarm (IP interface), CLR alarm (IP

interface), IP link failure (IP interface).

Summary of Contents for TPU-1






































































Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands

DIMAT TPU-1, Installation And Comissioning Manual

Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands