DIMAT TPU-1 Installation And Comissioning Manual Download Page 29 | Manualshive

Page: 29 / 69

background image

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

29/69

4.4

PROTECTION-SIDE INTERFACE MODULE

(CIRCUITS FROM ONE TO TWO COMMANDS)

Each IPTU protection-side interface module has a plug-in connector on the front plate, the

use of which is shown in Figure 24.

Figure 24 IPTU protection-side interface module connector

Each auxiliary relay is configurable from the Management System for command transmission

signalling, command output or alarm and, if be the case, unblocking. In the case of alarm, the

relay will act for one or more of the following causes:

RTC synchronization failure,

Telemeasuring failure, IEC 61850 link failure, Power-supply failure, Main module failure,

Module failure in slot (no.), Manual blocking (analog and digital), Automatic test failure (analog

and digital), Incorrect SIC security identification code (digital), Loss of synchronism (digital),

Incorrect identification code (digital), BER alarm (digital), Remote Alarm Indication (digital

IOCT type), Loss of signal (digital IOCT type), Reception blocking (analog), Error of reception

(analog), Low Signal/Noise ratio (analog), Signal loss (analog), Low guard-signal level/Excess

guard-signal level (analog), MTD alarm (IP interface), CDV alarm (IP interface), CLR alarm (IP

interface), IP link failure (IP interface).

The earth connection of the cable must be connected to the upper fixing screw. Make sure

that the module is completely fixed to the chassis.

«
...
27
28
29
30
31
...
»

Summary of Contents for TPU-1






































































Reviews:

No comments

Related manuals for TPU-1

Brand: Aastra Pages: 88

Brand: Vectron Pages: 80

Brand: National Instruments Pages: 8

digitalSTROM GR-TKM200

Brand: aizo Pages: 2

MorphoAccess SIGMA Series

Brand: Safran Pages: 517

Brand: red lion Pages: 8

Design Center 1000

Brand: Variquest Pages: 2

Brand: LAKS Pages: 24

Brand: Hioki Pages: 2

Brand: NEC Pages: 24

RemoteSAT RST100B

Brand: Beam Pages: 40

Brand: Tep Ex Pages: 15

Brand: XAC Pages: 4

Brand: XAC Pages: 6

Brand: Invenco Pages: 40

Brand: IBM Pages: 60

Brand: Metrologic Pages: 32

Brand: Valor Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands