DIMAT TPU-1 Installation And Comissioning Manual Download Page 55

Page: 55 / 69

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

55/69

ZATU.00 terminal block

The ZATU.00 terminal block is

associated with the ATPU

power-supply

module.

This

block contains five terminals:

two associated with the power

supply, which do not have

disconnect

devices

and

suitable for 0.2 to 4 mm

flexible conductors and for 0.2

to 6 mm

rigid conductors, and

three

associated

with

the

power-supply

alarm

relay,

which have disconnect devices

and suitable for up to 2.5 mm

flexible conductors and up to

4 mm

rigid

conductors.

Figure 37

shows

the

assignment of these terminals.

Figure 37 ZATU.00 terminal block

ZPTU.00 terminal block

The ZPTU.00 terminal block is

associated

with

the

IPTU

protection-side

interface

module. This block contains

fourteen terminals, which have

disconnect

devices

and

suitable for up to 2.5 mm

flexible conductors and up to

4 mm

rigid

conductors.

Figure 38

shows

the

assignment of these terminals.

Figure 38 ZPTU.00 terminal block

Summary of Contents for TPU-1






































































Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands

DIMAT TPU-1, Installation And Comissioning Manual

Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands