manualshive.com logo in svg

DIMAT TPU-1, Installation And Comissioning Manual, Page: 34 / 69

Share
Download
DIMAT TPU-1 Installation And Comissioning Manual Download Page 34

 

Communication solutions for power utilities 

UNIVERSAL TELEPROTECTION TPU-1 
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9  (May 2018) 

34/69 

5 

COMMISSIONING PROCEDURE 

5.1 

CHECKS 

1. 

Make sure that the conditions in which the terminal will operate are suitable (see section 

OPERATING AND STORAGE CONDITIONS 

in manual 

General Description

). 

2. 

Make  sure  with  the  help  of  a  multimeter,  that  the  power-supply  voltage  is  within  the 

range specified for the operating nominal voltage and, in the case of DC supply-voltage 

operation, that the polarity is correct. 

3. 

Make sure that the earth cables of the modules are connected correctly. 

4. 

Make sure that the connector (or connectors) of the line interface module (or modules) 

are connected correctly. 

5. 

Make  sure  that  the  connectors  of  the  MWTU  processing  module  are  connected 

correctly. 

6. 

As far as programming is concerned, it must be taken into account basic concepts such 

as:  operation  of  the  line  interface  module  (or  modules),  number  of  commands  in 

transmission  and  reception,  input  and  output  logic  desired,  duration  of  command 

transmission,  duration  of  command  output,  activation  condition  of  the  auxiliary 

relays, etc. 

5.2 

MODULE CONFIGURATION 

Without  the  power  supply  being  connected,  configure  in  the  IPTU  modules  the  nominal 

activation voltage of the command inputs. To do so, set the jumpers shown in Figure 7. 

The  modules  contain  components  sensitive  to  static  electricity,  so  great  care  must  be 

taken  when  handling  them.  It  is  advisable  to  use  an  antistatic  wristband  connected 

to earth. 

Summary of Contents for TPU-1






































































Reviews:

No comments