DIMAT TPU-1 Installation And Comissioning Manual Download Page 21 | Manualshive

Page: 21 / 69

background image

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

21/69

4.3

LINE INTERFACE MODULES

The TPU-1 terminal has one or two line interface modules, depending on whether it

manages one or two communication channels.

The line interface modules are divided into analog and digital line interface modules.

The digital line interface modules available are: IETU, IDTU, IOTU, IOCT and IPIT. The

analog line interface modules available are: IATU and IBTU.

4.3.1

IETU module

The IETU module gives a 64 kbit/s interface that can be programmed according to

Recommendations X.21/V.11, V.35 or G.703 of the ITU-T.

The IETU module has a 15-pin SUB-D connector on the front plate. Figure 14 to Figure 18

show the assignment of the contacts of the connector for the V.11, X.21, V.35, G.703

codirectional and G.703 contradirectional interfaces, respectively.

Figure 14 Use of the connector of the IETU module for V.11 interface

«
...
19
20
21
22
23
...
»

Summary of Contents for TPU-1






































































Reviews:

No comments

Related manuals for TPU-1

Brand: barclaycard Pages: 2

Brand: Bomex Pages: 41

Allen-Bradley 2713P-T10CD1

Brand: Rockwell Automation Pages: 114

Brand: RusGuard Pages: 20

Brand: VeriFone Pages: 56

Sammi Paytech SmartPay Plus

Brand: Sammi Paytech Pages: 66

Brand: TSYS Pages: 2

Brand: Ingenico Pages: 5

Brand: Ingenico Pages: 4

Brand: Ingenico Pages: 2

Brand: Ingenico Pages: 31

Brand: Ingenico Pages: 146

Brand: Datavan Pages: 20

Brand: Datavan Pages: 2

Brand: Heartland Pages: 15

Dinerware PAX S920

Brand: Heartland Pages: 16

Brand: PAX Pages: 65

Sonabeam E Series

Brand: fSONA Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands