manualshive.com logo in svg

DIMAT TPU-1, Installation And Comissioning Manual, Page: 24 / 69

Share
Download
DIMAT TPU-1 Installation And Comissioning Manual Download Page 24

 

Communication solutions for power utilities 

UNIVERSAL TELEPROTECTION TPU-1 
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9  (May 2018) 

24/69 

4.3.2 

IDTU module 

The  IDTU  module  gives  a  2 Mbit/s  interface  according  to  codirectional  G.703 

Recommendation of the ITU-T. 

Figure  19  shows  a  front  view  of  the  IDTU module.  As  can  be  seen  in  the  figure,  the  IDTU 

module has two BNC connectors (75 

Ω) and a RJ-45 connector (120 Ω) for twisted pair. The 

output impedance (75 

Ω or 120 Ω) according to the type of connector and whether the cable 

shield is connected to earth (output not balanced) or not (output balanced) is configured by 

internal settings. 

In  IDTU.00  modules  of  version  3.1,  the  type  of  connector  (BNC  or  RJ-45)  is  programmed 

from the TPU-1 Management System. 

Make sure that the module is completely fixed to the chassis. 

 

LEDs associated with the RJ-45 connector 

•

  Amber. It lights when there is BER alarm. 

•

  Green. It lights when there is synchronism. 

Figure 19

    Connectors of the 

IDTU line interface module of version IDTU.00 (3.0) 

Summary of Contents for TPU-1






































































Reviews:

No comments