manualshive.com logo in svg

DIMAT TPU-1, Installation And Comissioning Manual, Page: 6 / 69

Share
Download
DIMAT TPU-1 Installation And Comissioning Manual Download Page 6

 

Communication solutions for power utilities 

UNIVERSAL TELEPROTECTION TPU-1 
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9  (May 2018) 

6/69 

1 

MECHANICAL CHARACTERISTICS 

The  TPU-1  terminal  is  made 

up  of  a  19”  shelf  that  is  3  standard  units  (s.u.)  in  height, 

prepared for rack mounting. 

Figure 1 shows the general dimensions of the shelf as well as the position of the fastening 

holes. As can be seen in the figure, the shelf has one ventilation grid. 

 

Figure 1

   

General dimensions of the TPU-1 shelf 

The input and output of signals is carried out by means of the plug-in connectors located at 

the  rear  of  the  shelf.  If  one  wishes  the  external  connections  to  be  carried  out  through  a 

cabinet-mounting terminal block, it can be supplied on request, together with the necessary 

cables, see 

Appendix C

. 

During  installation  it  must  be  made  sure  that  the  ventilation  grid  is 

NOT

  covered.  Once 

the shelf has been installed, it must be checked that the ventilation grid on the top is 

NOT

 

obstructed in any way.   

When  installing  the  terminal  in  a  frame  of  a  cabinet,  in  order  to  improve  ventilation,  a 

space equivalent to at least one standard unit must be left above and below it. 

Summary of Contents for TPU-1






































































Reviews:

No comments