DIMAT TPU-1 Installation And Comissioning Manual Download Page 45

Page: 45 / 69

Communication solutions for power utilities

UNIVERSAL TELEPROTECTION TPU-1
INSTALLATION AND COMMISSIONING MANUAL Web version TPU-1R - Rev. 5.9 (May 2018)

45/69

Checking the transmission and the reception levels (analog line).

In the configuration page (

Line interfaces

submenu of the

Equipment

menu) check

the programmed values and check in line the actual values in the corresponding

terminals (Tx and Rx) measuring the guard signal using a selective voltmeter.

Checking the link

This operation involves cutting the teleprotection link

Properly program the identification codes (same local Tx et Rx values).

For full test terminal, make a permanent

local loop

in line (option

Loops, Blocking

and Test

option of the

Alignment

menu).

Before carrying out the loop, the command outputs of the terminal should be

suitably treated in order to make sure that no undesired output activation take place.

Carry out command transmission (

Input activation

option of the

Alignment

menu)

and check whether the activation has initiated the transmission of the desired

command, and the reception in case the terminal is not blocked.

Checking the relays

This operation involves cutting the teleprotection link

Since some of the alarm or signalling relays are connected to a telecontrol system,

it is important to check that the connections are correct.

In normal operating conditions, the relays programmed for alarm signalling are

active (C and T contacts closed) while, in the case of relays programmed for

transmission signalling, command output and unblocking, are NO active (C and R

contacts closed).

One way of energizing the relays is to program the blocking option of the

Alignment

menu of the Management System, if the programming associated with the relays

provides alarm generation under this circumstance.



Summary of Contents for TPU-1






































































Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands

DIMAT TPU-1, Installation And Comissioning Manual

Search results

Summary of Contents for TPU-1

Reviews:

Related manuals for TPU-1

Brands by name

Popular brands