Digi IX14 User Manual Download Page 120 | Manualshive

Page: 120 / 828

background image

Interfaces

Local Area Networks (LANs)

IX14 User Guide

120

About Local Area Networks (LANs)

A Local Area Network (LAN) connects network devices together in a logical Layer-2 network.

The following diagram shows a LAN connected to the

LAN

Ethernet device. Once the LAN is configured

and enabled, the devices connected to the network interfaces can communicate with each other, as
demonstrated by the

ping

commands.

Configure a LAN

Configuring a Local Area Network (LAN) involves configuring the following items:

Required configuration items

n

The interface type: either

Ethernet

,

IP Passthrough

, or

PPPoE

.

n

The firewall zone:

Internal

.

n

The network device that is used by the LAN.

n

The IPv4 address and subnet mask for the LAN. While it is not strictly necessary for a LAN to
have an IP address, if you want to send traffic from other networks to the LAN, you must
configure an IP address.

Note

By default,

LAN

is set to an IP address of 192.168.2.1 and uses the IP subnet of

192.168.2.0/24. If the

LAN

Ethernet device is being used by a WAN with the same IP subnet, you

should change the default IP address and subnet of LAN1.

Additional configuration items

n

Additional IPv4 configuration:

l

The metric for IPv4 routes associated with the LAN.

l

The relative weight for IPv4 routes associated with the LAN.

l

The IPv4 management priority of the LAN. The active interface with the highest
management priority will have its address reported as the preferred contact address for
central management and direct device access.

l

The IPv4 Maximum Transmission Unit (MTU) of the LAN.

l

When to use DNS: always, never, or only when this interface is the primary default route.

l

IPv4 DHCP server configuration. See

for more information.

n

IPv6 configuration:

l

The metric for IPv6 routes associated with the LAN.

l

The relative weight for IPv6 routes associated with the LAN.

l

The IPv6 management priority of the LAN. The active interface with the highest
management priority will have its address reported as the preferred contact address for
central management and direct device access.

l

The IPv6 Maximum Transmission Unit (MTU) of the LAN.

l

When to use DNS: always, never, or only when this interface is the primary default route.

«
...
118
119
120
121
122
...
»

Summary of Contents for IX14





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IX14

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

Brand: Keithley Pages: 59

Brand: Ubiquiti Pages: 50

OXTOPUS EIA-709

Brand: OCCITALINA Pages: 54

Brand: Hama Pages: 24

Brand: iNetVu Pages: 20

Brand: Paradyne Pages: 74

Brand: DPS Pages: 57

IP Board IPT10000C

Brand: Dialogic Pages: 2

Air Live GW-300R

Brand: Ovislink Pages: 20

EZ Switch SMC-EZ1024FDT

Brand: SMC Networks Pages: 4

Brand: Cradlepoint Pages: 2

Brand: Nexxt Pages: 2

Brand: Belkin Pages: 2

Brand: Supero Pages: 66

Brand: National Instruments Pages: 72

Firebox T85-PoE

Brand: Watchguard Pages: 27

Digi Connect WAN

Brand: Digi Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands