manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 8

Introduction

1-4 — Orbitor 3000 Reference Manual

Protocol

The protocol section is used to indicate the protocol being used by the transport layer.  This could be TCP, UDP,
or something else.

Time to live

The time to live section is used to prevent a frame from traversing the network forever.  This field contains a
number (maximum 255) that is set when the frame is originally generated.  Each time the frame is passed through
the bridge/router, the bridge/router will decrement the time to live by two.  When the time to live reaches zero,
the frame is discarded.

Header Checksum

The header checksum is used to verify the data in the IP header.  The IP header is recalculated each time a frame
is passed through a router.  The recalculation is necessary because the time to live field is changed.

Fragmentation

Fragmentation occurs when an IP frame must be split up into smaller IP frames.  When the originating device
generates the IP frame, the device is not aware of all the paths the frame must traverse to get to the destination
device.  If the IP frame is to pass through a network that has small packet capabilities, the IP frame must be split
up and reassembled at the destination device.  Each of the fragments is assigned a fragment offset value, which
determines where the fragment fits into the original IP frame.

The Orbitor Ethernet bridge/router will accept fragmented frames directed to itself and reassemble them, but it
will not fragment frames.

Options

There are various options that may be set for any IP frame.

Source Routing

Source routing is used to predetermine the path that the IP frame must travel through the network.  There are two
types of source routing: strict source routing and loose source routing.

Strict source routing will contain a list of IP addresses of routers that must be used when the IP frame is sent
through the network.  Strict source routing is used mainly to provide some type of data security.  Once the IP
frame has reached the destination station, the destination station will take the list of IP addresses from the options
field, reverse them, and use them for a strict route back to the originating station.

Loose source routing will also contain a list of IP address of routers to be used on the path to the destination
station.  However, the IP frame may pass through other intermediate routers to get to the next IP address in the
loose source routing list.

Route Recording

Route recording simply keeps a list of all the IP addresses of the routers that the IP frame has passed through on
its way to the destination station.

Time Stamps

The time stamp option is used to record the time at which the IP frame passed through each router on its way to
the destination station.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands