manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 48

Event Logs

A-6 — Orbitor 3000 Reference Manual

Running in BOOT mode

Generated when the bridge/router is starting in Boot mode.  This is the mode for software upgrades.
Once the software upgrade has been successfully completed, the bridge/router restarts in Operational
mode.

Running in OPERATIONAL mode

Generated when the bridge/router is starting in Operational mode.  This is the mode for normal
operations of the bridge/router.

SNMP authentication failure for X

Generated when an SNMP authentication failure is detected.  The SNMP message source is specified by
its IP address.

SNMP has stopped

Generated when SNMP is deactivated by removing the bridge/router’s IP address definition.

SNMP is running

Generated when SNMP is activated by defining an IP address for the bridge/router.

Starting IPCP negotiation with <remote site alias>

Generated when the Internet Protocol Control Protocol negotiation has been initiated with the remote site
device associated with the stated remote site profile.

Starting IPXCP negotiation with <remote site alias>

Generated when the Internet Packet Exchange Control Protocol negotiation has been initiated with the
remote site device associated with the stated remote site profile.

Station address table has been filled

Generated when the station address table is filled.  This event is not regenerated until the table size drops
below 3/4 full and then fills again.

STP disabled

Generated when STP is disabled.

STP enabled

Generated when STP is enabled.

STP is running

Generated when STP is activated.

STP port X is enabled

Generated when STP port is enabled.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands