manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 56

Event Logs

A-14 — Orbitor 3000 Reference Manual

* PVC X down

Generated when PVC X is lost.

* PVC X up

Generated when PVC X is established.

* Results of IPCP negotiation are incompatible, disconnecting remote site AA

Generated when IPCP negotiations with a remote site PPP router result in a incompatible IP
configuration.  The remote site is then disconnected.

* STP forming new bridge net

Generated when the STP control bridge is lost causing a new control bridge to be chosen.

* STP lost all connections

Generated when all STP connections are lost.

* TFTP: Abort. ACK retry exceeded

Aborted a TFTP session because the bridge/router did not receive a new data packet within the TFTP
“T1” times “N2” interval.

* TFTP: Abort. ACK timeout

Aborted a TFTP session because the bridge/router did not receive an ACK for the last data packet it sent
within the TFTP “T1” times “N2” interval.

* TFTP: Abort. Error (#) received

Aborted a TFTP session because of the reception of a TFTP error message from the connected device.
The errors are: 0 - not defined, 1 - file not found, 2 - access violation, 3 - disk full or allocation exceeded,
4 - illegal TFTP operation, 5 - unknown transfer ID, 6 - file already exists, 7 - no such user.

* Unable to compress

Generated when one bridge/router has compression enabled and the peer bridge/router does not (i.e. the
peer bridge/router does not have compression hardware or has compression disabled).

* Unable to route. UDP failure

Generated when the device tried to open an already open UDP channel, causing IP routing to fail.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands