manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 69

Programmable Filtering

B-12 — Orbitor 3000 Reference Manual

Mask Combinations

Mask combinations may be required to ensure that a frame is sufficiently qualified before the decision to filter is
made.  The qualification a frame must go through before a filter decision is made depends on the reason for the
filter.  Nonetheless, a few examples below have been provided that should aid in the creation of a mask that may
require that extra little bit of qualification.

Example

To prevent a specific Ethernet station from accessing any TCP/IP host on the other segment.  Assume the
Ethernet address is 01-02-03-04-05-06.

The mask would be:

6-010203040506&12-0800&23-06

Example

To prevent a specific protocol type from accessing a specific Ethernet Address.  Assume the Ethernet address is
01-02-03-04-05-06, and the protocol type is Appletalk

®

.  The filter mask would be:

0-010203040506&12-

809B

Example

To prevent any Ethernet address with the 10th bit set to a 0 from accessing a LAT host or an IP host with an
Internet address of 128.001.001.128.

This particular mask, although not particularly useful, might be best served by creating two masks instead of one
long mask.  The decision is up to the Bridge Manager, but a longer mask is always more difficult to understand
later.  Both methods are presented below:

Combined Filters

4-X’XX0X’&(12-6004|(12-0800&30-80010180))

Separate Filters 4-X’XX0X’&12-6004

4-X’XX0X’&12-0800&30-80010180

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands