manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 50

Event Logs

A-8 — Orbitor 3000 Reference Manual

The possible alarm logs are presented here in alphabetical order.

* Activation Failure

Generated when the activation attempt has failed.

* Activation In Progress (NT)

Generated when the bridge/router initiates the activation of the module and circuit.

* Activation In Progress (LT)

Generated when the central office initiates the activation of the module and circuit.

* Battery is getting low

Generated on startup when the battery is detected to be low.

* Call X connected

Generated when an ISDN call has completed connection and is ready to start B channel communication.

* Call X disconnect.  Cause: X

Generated when the disconnect of an ISDN call is completed.  This event is generated on both sides of
the ISDN call.  The cause will be one of the causes as specified in the CCITT Recommendation Q.931.
Causes of “normal call clearing”, “User busy”, and “Number changed” are printed in words, all other are
numeric.

Code

Description

001

Unallocated/unassigned number

002
003
004
006
007
008
009
010
011
016

No route to specified transit network
No route to destination
Channel unacceptable
Channel unacceptable
Call awarded and being delivered in an established channel
Prefix 0 dialed but not allowed
Prefix 1 dialed but not allowed
Prefix 1 dialed but not required
More digits received than allowed, call is proceeding
Normal call clearing

017

User busy

018

No user responding

019
020
021

No answer from user
Circuit operational
Call rejected

022

Number changed

023
024
025
026
027
028

Reverse charging rejected
Call suspended
Call resumed
Non-selected user clearing
Destination out of order
Invalid number format

029

Facility rejected

030
031

Response to STATUS INQUIRY
Normal, unspecified

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands