manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 47

Event Logs

Orbitor 3000 Reference Manual— A-5

No NCP's open, tearing link down

Generated when a PPP link does not have a Network Control Protocol operating.  This may be due to
IPCP and IPXCP being disabled, or the NCP connection was not negotiated to completion.

Partner will disable a link

Generated after detection of two “multipoint” links connected to the same partner bridge/router.  The
bridge/router with the higher MAC address prints this event.

Password timer has expired

Generated when a bridge/router has issued the password prompt for a Telnet connection and timed out
waiting for the password to be supplied.

PVC X status enquiry unacknowledged.

Generated when the Frame Relay switch fails to respond to a status enquiry in the requisite time.

PVC X transmit limit decreased to xxxxx (FECN)

Generated when congestion conditions on the WAN are indicated because the number of FECN frames
received, exceeded the number of clear frames, in the last time interval.

PVC X transmit limit increased to xxxxx

Generated when congestion conditions on the WAN are alleviated because the number of FECN frames
received, was exceeded by the number of clear frames, in the last measurement interval.

PVC X transmit limit set to CIR (BECN)

Generated when a BECN has been received.

PVC X transmit decreased to xxxxx (idle)

Generated when no BECN frames have been received in the last measurement interval, and BECN
throttling is set.

PVC X unrecognized LMI frame

Generated when an unparseable frame is received on the management DLCI.

Refused connection attempt from X

Generated when a request for connection is refused because a previous connection exists.  The connecting
bridge/router’s IP address is specified.

Request for connection from X, accepted

Generated when a Telnet connection is accepted.  The connecting bridge/router’s name or IP address is
specified.

Restoring boot configuration

Generated when the bridge/router is starting in boot EPROM or flash and there is configuration
information stored in EEPROM.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands