manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 57

Event Logs

Orbitor 3000 Reference Manual— A-15

The possible PPP security logs are presented here in alphabetical order.

Link X CHAP failed for A (Y)

Generated when the remote site PPP router failed a CHAP authentication request from this Orbitor.  The
remote site name (A) and ISDN number (Y) are displayed if know.

Link X CHAP failed to complete (Y)

Generated when the remote site PPP router sent a CHAP challenge and this Orbitor sent a response, but
no further information was received from the remote site router. The ISDN number (Y) is displayed if
know.

Link X CHAP login refused by A (Y)

Generated when the remote site PPP router sent a CHAP challenge and this Orbitor sent a response, and
the remote site router refused the connection. The remote site name (A) and ISDN number (Y) are
displayed if know.

Link X PAP failed for A (Y)

Generated when the remote site PPP router failed a PAP authentication request from this Orbitor.  The
remote site name (A) and ISDN number (Y) are displayed if know.

Link X PAP failed to complete (Y)

Generated when the remote site PPP router sent a PAP password request and this Orbitor sent the PAP
password in reply, but no further information was received from the remote site router. The ISDN
number (Y) is displayed if know.

Link X PAP peer failed to authenticate

Generated when the remote site PPP router did not respond to a request to authenticate.

Link X refused to authenticate (Y)

Generated when the remote site PPP router refused to do authentication.  The ISDN number (Y) is
displayed if know.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands