manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 49

Event Logs

Orbitor 3000 Reference Manual— A-7

STP port X is disabled

Generated when STP port is disabled.

TFTP: stop putting filename to WWW.XXX.YYY.ZZZ

The bridge/router has sent the final data packet of a file (filename), but has timed out before receiving the
final ACK.  The session may or may not have succeeded in delivering the entire file.

TFTP: WWW.XXX.YYY.ZZZ finished getting filename

The bridge/router has sent the final packet of a file (filename) that a LAN device with IP address
WWW.XXX.YYY.ZZZ was getting from the bridge/router.

TFTP: WWW.XXX.YYY.ZZZ finished putting filename

The bridge/router has ACK-ed the last packet of a file (filename) that a LAN device with IP address
WWW.XXX.YYY.ZZZ was putting onto the bridge/router.

TFTP: WWW.XXX.YYY.ZZZ getting filename

A LAN device with IP address WWW.XXX.YYY.ZZZ is getting a file (filename) from the bridge/router.

TFTP: WWW.XXX.YYY.ZZZ putting filename

A LAN device with IP address WWW.XXX.YYY.ZZZ is putting a file (filename) onto the bridge/router.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands