Develcon Electronics DI-1135 Reference Manual Download Page 46

Page: 46 / 74

Event Logs

A-4 — Orbitor 3000 Reference Manual

Link X - CSU/DSU reset

Generated when the Orbitor has initiated a reset of the CSU/DSU link module.

Link X - CSU/DSU self test results - total: XXXX; good: YYYY (ZZ.ZZ%); errored: A (B.BB%)

Generated after the CSU/DSU link module has completed a self test.

Link X - external loopback results - total: XXXX; good: YYYY (ZZ.ZZ%); errored: A (B.BB%)

Generated after the CSU/DSU link module has completed an external loopback.

Link X LCP establishing

Generated when the Link Control Protocol of a PPP link is establishing between this device and the
remote site PPP device.

Link X LCP operational

Generated when the Link Control Protocol of a PPP link has been negotiated and is now operational
between this device and the remote site PPP device.

Link X no reply to Y Echo-Requests

Generated just prior to a link going down. The link has gone down due to no replies to the echo request
messages sent.

Link X peer authenticating with PAP

Generated when the peer (remote) device is using PAP to authenticate this device.

Link X peer authenticating with CHAP

Generated when the peer (remote) device is using CHAP to authenticate this device.

Link X received Protocol-Reject for <protocol>

Generated when the peer (remote) device rejects one of the Network Control Protocols.

Link X re-establishing due to multilink mismatch

Generated when the link re-negotiates the LCP parameters due to the Multilink states not matching on
each end of the link.

Link X retry timer too short

Generated if the T1 timer is less than twice the time to transmit the largest possible frame.

Multipoint links to same remote partner

Generated after detection of two “multipoint” links connected to the same partner bridge/router.

Network resynchronization

Generated when compression resynchronization has been completed.

Summary of Contents for DI-1135










































































Search results

Summary of Contents for DI-1135

Reviews:

Brands by name

Popular brands

Develcon Electronics DI-1135, Reference Manual

Search results

Summary of Contents for DI-1135

Reviews:

Brands by name

Popular brands