Develcon Electronics DI-1135 Reference Manual Download Page 45

Page: 45 / 74

Event Logs

Orbitor 3000 Reference Manual— A-3

Link X - CSU/DSU connected

Generated when the CSU/DSU link module has established a connection to the remote partner
CSU/DSU.

Link X - CSU/DSU CSU telco loopback started

Generated when the telco has initiated a CSU loopback to this CSU/DSU link module

Link X - CSU/DSU CSU telco loopback ended

Generated when the telco has terminated the CSU loopback to this CSU/DSU link module

Link X - CSU/DSU DSU telco loopback started

Generated when the telco has initiated a DSU loopback to this CSU/DSU link module

Link X - CSU/DSU DSU telco loopback ended

Generated when the telco has terminated the DSU loopback to this CSU/DSU link module

Link X - CSU/DSU digital loopback results - total: XXXX; good: YYYY (ZZ.ZZ%); errored: A (B.BB%)

Generated after the CSU/DSU link module has completed a digital loopback test.

Link X - CSU/DSU initialized

Generated when the CSU/DSU link module has completed initialization and has established
communications with the Orbitor.

Link X - CSU/DSU line out of service

Generated when the CSU/DSU is in communication with the local telco, but is not connected to the
remote partner CSU/DSU.

Link X - CSU/DSU no signal

Generated when the CSU/DSU link module cannot establish communications with the local telco.

Link X - CSU/DSU remote loopback ended - line unconnected

Generated when the CSU/DSU link module cannot establish a connection to the remote partner
CSU/DSU to perform a remote loopback test.

Link X - CSU/DSU remote loopback results - total: XXXX; good: YYYY (ZZ.ZZ%); errored: A (B.BB%)

Generated after the CSU/DSU link module has completed a remote loopback test.

Link X - CSU/DSU remote slave loopback started

Generated when the remote partner CSU/DSU has initiated a loopback to this CSU/DSU link module

Link X - CSU/DSU remote slave loopback ended

Generated when the remote partner CSU/DSU has terminated the loopback to this CSU/DSU link module

Summary of Contents for DI-1135










































































Search results

Summary of Contents for DI-1135

Reviews:

Brands by name

Popular brands

Develcon Electronics DI-1135, Reference Manual

Search results

Summary of Contents for DI-1135

Reviews:

Brands by name

Popular brands