manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 52

Event Logs

A-10 — Orbitor 3000 Reference Manual

* Call X disconnected due to switch type change

Generated when the operator changes the ISDN switch type while an ISDN call is in progress.

* Call X initiated to number #

Generated when an ISDN call is initiated to the specified number.

* Call X registered

Generated when the SPID is correctly sent to the central switch and the switch has accepted the SPID.

* Call X registration failed

Generated when the SPID is sent to the central switch and the switch has not accepted the SPID.

* Compressor DMA lock up

Generated when the device detects that the compressor DMA has locked up.

* Compression negotiation failure (#)

Generated when a failure condition causes a link to be reset.

* Configuration too large to be saved

Generated when the bridge/router attempts to save a configuration that does not fit in the reserved area of
non-volatile RAM.

* Connection to LAN X failed, trying ...

Generated when failure of the LAN interface external loopback test is detected.

* Detected Phantom Power

Generated when the ISDN WAN interface module has properly detected the phantom power signal from
the ISDN switch.

* Device DEVXXXXXX connected

Generated when a connection to the specified bridge/router is established.

* Device DEVXXXXXX disconnected

Generated when a connection to the specified bridge/router is lost.

* Dictionaries out of sync

Generated when the device detects that the compression dictionaries are out of sync.

* Entering Maint ILMT Mode

Generated when the central office invokes an Insertion Loss Measurement Test command.  During the
test mode the module is not available for use by the bridge/router.  This test is as per the ANSI
specification in ANSI T1.601-1992.

* Entering Maint QUIET Mode

Generated when the central office invokes a testing mode.  During the test mode the module is not
available for use by the bridge/router.  This test is as per the ANSI specification in ANSI T1.601-1992.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands