manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 3

Contents 

(continued)

Filled Address Table ............................................................................................................................................... 1-14

O

RBITOR 

E

THERNET 

B

RIDGE

/R

OUTER 

F

EATURE 

D

EFINITIONS

.................................................................................... 1-15

Telnet ..................................................................................................................................................................... 1-15
Link Compression................................................................................................................................................... 1-15
WAN Topologies.................................................................................................................................................... 1-17

Point-to-Point ..................................................................................................................................................... 1-17
Multipoint .......................................................................................................................................................... 1-17

Bandwidth On Demand........................................................................................................................................... 1-17

Disaster Recovery............................................................................................................................................... 1-18
Time of Day Connect Application ...................................................................................................................... 1-18

Point-to-Point ................................................................................................................................................. 1-18
Multipoint ...................................................................................................................................................... 1-19

Disaster Recovery Backup Link .............................................................................................................................. 1-19
ISDN Single Active Link & Dual Active Link ........................................................................................................ 1-19
Operating Software Upgrades ................................................................................................................................. 1-19

SECTION 2 — ISDN CONNECTION MANAGEMENT.................................................2-1

Orbitor ISDN Connection Management .................................................................................................................... 2-1

Wide Area Network Topologies Supported ........................................................................................................... 2-1
Call Establishment Methods ................................................................................................................................. 2-1

Auto-Call (Time-of-Day Connections).............................................................................................................. 2-2
Address Connect .............................................................................................................................................. 2-3
Manual Call...................................................................................................................................................... 2-3
Combination..................................................................................................................................................... 2-4

Connection Process............................................................................................................................................... 2-4

Protocol Awareness .......................................................................................................................................... 2-5
Suspension Process........................................................................................................................................... 2-5
Interesting Traffic............................................................................................................................................. 2-5
Idle Timer ........................................................................................................................................................ 2-6
Orbitor Session Participation (Spoofing)........................................................................................................... 2-6
Termination Process ......................................................................................................................................... 2-7

IP Specifics .......................................................................................................................................................... 2-7

IP Address Connect .......................................................................................................................................... 2-7
Suspension of TCP/IP Sessions ........................................................................................................................ 2-7
RIP—Routing Information Protocol ................................................................................................................. 2-7

IPX Specifics........................................................................................................................................................ 2-8

RIP/IPX and SAP/IPX...................................................................................................................................... 2-8
Suspension of IPX Sessions.............................................................................................................................. 2-8

Server IPX Watchdog Frames....................................................................................................................... 2-8
Client IPX Watchdog Frames ....................................................................................................................... 2-8

IPX Serialization Frames .................................................................................................................................. 2-8

SECTION 3 — LINK INTERFACES REFERENCE ......................................................3-1

P

INOUT 

I

NFORMATION

.................................................................................................................................................. 3-1

L

INK 

C

LOCKING 

I

NFORMATION

..................................................................................................................................... 3-1

CSU/DSU L

INK 

M

ODULE 

I

NFORMATION

...................................................................................................................... 3-1

Console Pinouts ........................................................................................................................................................ 3-2
V.24 & RS232C Link Pinouts................................................................................................................................... 3-3
V.11 & X.21 Link Pinouts ........................................................................................................................................ 3-4
RS442 & RS530 Link Pinouts .................................................................................................................................. 3-5
V.35 Link Pinouts..................................................................................................................................................... 3-6
RS232 Null-Modem Cable Configuration ................................................................................................................. 3-7
V.35 Null-Modem Cable Configuration .................................................................................................................... 3-8
RS530 Null-Modem Cable Configuration ................................................................................................................. 3-9

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands