manualshive.com logo in svg

Develcon Electronics DI-1135, Reference Manual

Share
Download
Develcon Electronics DI-1135 Reference Manual Download Page 43

Orbitor 3000 Reference Manual— A-1

Appendix A —  Event Logs

The Orbitor Ethernet bridge/router generates event logs for various functions performed by the bridge/router.  All of the
event logs are stored in the internal event log file, that is accessible through the Network Events menu.

Certain event logs are classified as alarms because they are not informational events.  Alarm logs are indicated by an
asterisk (“*”) at the start of the alarm text and are printed on the ALARM line on the menu system as well as being stored
in the event log.

All WAN-link-related events include the link number in the event log.

The possible event logs are presented here in alphabetical order.

Aggregate link speed too high

Generated when the maximum aggregate link speed is exceeded.

Call X is busy, incoming call rejected

Generated when an ISDN call comes in for a number (link) that is already connected to another call.

Call X is busy during reset, disconnecting

Generated when either the directory number or the SPID has been changed for an ISDN call and the call
is being re-initialized but the call is currently in progress.

Call X - state X

Generated when the ISDN call changes states.  The states are as follows: Null, Proceeding, Active, and
Disconnecting.

Capture off

Generated when link trace capture is turned off.

Completed IPCP negotiation with <remote site alias>

Generated when the Internet Protocol Control Protocol negotiation has been completed with the remote
site device associated with the stated remote site profile.  Once IPCP negotiations are complete, IP
routing may take place between the two routers.

Completed IPXCP negotiation with <remote site alias>

Generated when the Internet Packet Exchange Control Protocol negotiation has been completed with the
remote site device associated with the stated remote site profile.  Once IPXCP negotiations are complete,
IPX routing may take place between the two routers.

Configuration restored

Generated during a warm start when a configuration is successfully restored from non-volatile RAM.

Summary of Contents for DI-1135











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands